Description
The SI Modular Guide Rod for GLOCK™ GEN3 is a stainless steel, customizable system that accepts any aftermarket compatible GLOCK™ Spring as well as Strike Industries’ custom recoil spring weights. Its stainless steel shaft and anodized aluminum end cap will not rust, crack or break as easily as polymer rods found in oem Glock pistols, increasing it’s service life compared to standard recoil assemblies. Fine tune your recoil characteristics and improve reliability by using our recoil springs offered in various weights without having to buy more than one guide rod. Simply unscrew the endcap, replace the spring to your preference, replace the end cap and you’re good to go!
SI also offers the end caps in various colors and designs to add a custom look and more personalization to your pistol.
Contents:
– 1x GMGR : SUS303
– 3x endcaps: 7075 T6 Aluminum
– 2x 0.2mm shims: SUS304
– 1x 0.4mm shims: SUS304
Instructions: The varieties of included shims are to ensure the guide rod fits a wide variety of compatible GLOCK™ slides. Begin with just the 0.4mm shim and test for fit and function. the shims also change how flush the end cap is to the front of the slide.
Compatibility: For G17,17L,22,24,31,34,35,37
DESCRIPTION:
The SI Modular Guide Rod for GLOCK™ GEN3 is a stainless steel, customizable system that accepts any aftermarket compatible GLOCK™ Spring as well as Strike Industries’ custom recoil spring weights. Its stainless steel shaft and anodized aluminum end cap will not rust, crack or break as easily as polymer rods found in oem Glock pistols, increasing it’s service life compared to standard recoil assemblies. Fine tune your recoil characteristics and improve reliability by using our recoil springs offered in various weights without having to buy more than one guide rod. Simply unscrew the endcap, replace the spring to your preference, replace the end cap and you’re good to go!
SI also offers the end caps in various colors and designs to add a custom look and more personalization to your pistol.
Contents:
– 1x GMGR : SUS303
– 3x endcaps: 7075 T6 Aluminum
– 2x 0.2mm shims: SUS304
– 1x 0.4mm shims: SUS304
Instructions: The varieties of included shims are to ensure the guide rod fits a wide variety of compatible GLOCK™ slides. Begin with just the 0.4mm shim and test for fit and function. the shims also change how flush the end cap is to the front of the slide.
Compatibility:
For G17,17L,22,24,31,34,35,37
Features:
– Easily swap different spring weights.
– Made from 303 Stainless Steel for corrosion resistance and increased toughness.
– Adjustable fit with the included shims even allows compatibility with our Jitterplug for GLOCK™ GEN3 upgrade.
– Endcaps available in 4 different colors, and 3 different designs.
Product Specifications:
– Shaft ID: 0.223”
– OD: 0.41”
– Length: 3.10” (without shims)
NOTE: These are for GLOCK™ GEN3 size Guide Rods.
NOTE: Very light reduced power springs may not function 100% in stock platforms when feeding from reduced capacity magazines.
NOTE: Use of medium strength thread locker to the endcap threads during installation is highly recommended.
DISCLAIMER:
-This product is not manufactured, authorized, endorsed, or warranted by GLOCK. GLOCK does not warrant or represent that this product is compatible with GLOCK pistols.
–“GLOCK” is a federally registered trademark of GLOCK, Inc. and is one of many trademarks owned by GLOCK, Inc. and GLOCK Ges.m.b.H. Neither Strike Industries Inc. nor this site are affiliated in any manner with, or otherwise endorsed by, GLOCK, Inc. or GLOCK Ges.m.b.H. The use of “GLOCK” on this page is merely to advertise the sale of GLOCK pistols, parts, or components. For additional genuine GLOCK, Inc. and GLOCK Ges.m.b.H products and parts visit www.glock.com.
-CALIFORNIA PROPOSITION 65 WARNING:-
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information: www.P65Warnings.ca.gov
Reviews
There are no reviews yet.